CamBall4 XM

CamBall4-XM PTZ Camera Broadcast for Film and TV

The Camball4 XM (Extended Motion) is possibly the most advanced and feature-rich Broadcast PTZ camera of its type on the market. Evolved over 15 years and always upgradeable, the PTZ Camera has a track record beyond any other. Here are some of the standard features found only on the Camball4;

As an outdoor PTZ camera, it is weatherproof and rugged.  Made from carbon fibre, with slip rings, wide dynamic range, positional metadata, profile moves, DMX control, motion control, advanced CCU control.

Our Remote Cameras are used in sport, reality shows, wildlife and concert tours.

The iBase is an add-on feature which can be specified to add the options of IP control, fibre control and pictures over fibre, all built into the broadcast PTZ Camera. To find out more, take a look at the CamBall4 XMi Webpage

For further information on the Remote Controlled PTZ Camera, CamBall4 XM download the CamBall4 XM Brochure 

For further information on the PTZ IP Network Camera download the CamBall4 XMi Brochure 

  • DMX, Free D, M*, Motion Control Protocols
  • Real Time Metadata for VR & AR
  • Built in Move Profiles
  • Weatherproof & Rugged Carbon Fibre
  • 2.4 Megapixel Sensor to 1080p
  • WDR mode
  • Enhanced CCU Control
  • Genlock
  • 30x optical zoom
  • Slip Rings
  • Inverted or Upright Mounting
  • 64 Pre-set positions P,T, Z, F
  • Switchable to Infra-Red sensitive
  • Internal Wide Angle Converter options
  • Internal Heater Option
  • Weight: 2.9kg(S) – 3.1kg(XM)
    Dimensions: W.166mm, H.222mm, D.206mm (+ connectors)
    Data: RS485, Dstar, DMX, Free-D, Mstar
    Power: 12-16v @ 1A

    Pan Range: 360deg. Continuous. (DMX 720 deg.)
    Tilt Range: +/- 120deg from vertical.
    Pan Speed Range: <0.05deg/sec - >180deg/sec.Other ratios on request.
    Tilt Speed Range: <0.03deg/sec - >120deg/sec.Other ratios on request.

    Accuracy: 0.0055deg (positional) <0.005deg (joystick)
    Pre-Set Positions: 64, 16bit accuracy (+/- 0.0055deg. theoretical)

    Other features: Profile Move with Ramp Up, Ramp Down, Total Time, Pan/Tilt Speed, proportional to zoom angle, LCD status screen, Tally Light

    Camera Sensor: 0.36” NMOS
    Active Pixels: 2.38 Mpixels
    Sig /Noise Ratio: >50dB

    HFOV: 30x zoom – 64deg. to 2.3deg
    MOD: <30cm
    Distortion: <3% (wide)
    Iris: F1.6 - F28
    Sensitivity: 30x 1.4 lux. (F1.6 AGC On)

    HD Standards: 1080i/50/60, 720p/50/60, 1080p/50/60 HDSDI

  • XLR4 - Power & RS485 data
  • BNC1 – HDSDI
  • BNC2 – Genlock

    Remote: Pan, Tilt, Zoom, Iris, Focus, Auto / Manual White, Preset White, Rgain,Bgain, Master Pedestal, Red Pedestal, Blue Pedestal, Shutter, Gain, Gamma, Dzoom On/Off, Auto Iris On/Off, Auto Focus On/Off, IR Mode On/Off, Chroma, Detail, Shading, Knee, WDR, RGB balance, Output Standard etc.Preset Store (P,T,Z,F), Preset Recall, GoTo Absolute Position,P,T reverse, speeds 1-10, Turbo Speed, ND Filter.

    Operating Temp: -10 to >+40degC Out of sunlight
    Sealed: IP65 minimum (IP66 option)
    Mounting: 2 x 3/8”, 2 x 1/4” + safety bond point

    ‘DMX Control’:
  • 8 channels - Pan (2Ch), Tilt (2Ch), Zoom (2Ch), Focus (1Ch), Iris (1Ch)
  • 16bit positioning – 720deg. Pan

    Specifications subject to change without notice E & OE
  • For further information on the CamBall4 XM download the CamBall4 XM Brochure

    For further support on the CamBall4 XM download the CamBall4 XM Instruction Manual

    If you have any questions download the CamBall4 XM FAQ

    For help with IP Multicaster Setup download the Instruction Manual