Camball4 VRi

CamBall4 VRi Broadcast PTZ Camera Remote for film and television
CamBall4 VRi Broadcast PTZ Camera Remote for film and television CamBall4 VRi Broadcast Remote PTZ Camera for film and television

Adding the iBase to the Camball4 VRi (Virtual Reality) adds a further level of functionality to the standard Camball4 VR. The standard features include;

As an outdoor PTZ camera, it is weatherproof and rugged.  Made from carbon fibre, with slip rings, wide dynamic range, positional metadata, profile moves, VR and AR capable, DMX control, motion control, advanced CCU control.

In addition to these, the iBase adds the options of IP control, fibre control and pictures over fibre, all built into the iBase.

For further information on the CamBall4 VRi download the CamBall4 VRi Brochure

  • DMX, Free D, M*, Motion Control Protocols
  • Real Time Metadata for VR & AR
  • Built in Move Profiles
  • Weatherproof & Rugged Carbon Fibre
  • 2.4 Megapixel Sensor to 1080p
  • WDR mode
  • Enhanced CCU Control
  • Genlock
  • 30x optical zoom
  • Slip Rings
  • Inverted or Upright Mounting
  • 64 Pre-set positions P,T, Z, F
  • Switchable to Infra-Red sensitive
  • Internal Wide Angle Converter options
  • Internal Heater Option
  • 16bit absolute shaft encoders
  • Weight: 2.9kg(S) – 3.1kg(XM)
    Dimensions: W.166mm, H.222mm, D.206mm (+ connectors)
    Data: RS485, Dstar, DMX, Free-D, Mstar
    Power: 12-16v @ 1A

    Pan Range: 360deg. Continuous. (DMX 720 deg.)
    Tilt Range: +/- 120deg from vertical.
    Pan Speed Range: <0.05deg/sec - >180deg/sec.Other ratios on request.
    Tilt Speed Range: <0.03deg/sec - >120deg/sec.Other ratios on request.

    Accuracy: 0.0055deg (positional) <0.005deg (joystick)
    Pre-Set Positions: 64, 16bit accuracy (+/- 0.0055deg. theoretical)

    Other features: Profile Move with Ramp Up, Ramp Down, Total Time, Pan/Tilt Speed, proportional to zoom angle, LCD status screen, Tally Light

    Camera Sensor: 0.36” NMOS
    Active Pixels: 2.38 Mpixels
    Sig /Noise Ratio: >50dB

    HFOV: 30x zoom – 64deg. to 2.3deg
    MOD: <30cm
    Distortion: <3% (wide)
    Iris: F1.6 - F28
    Sensitivity: 30x 1.4 lux. (F1.6 AGC On)

    HD Standards: 1080i/50/60, 720p/50/60, 1080p/50/60 HDSDI

    Connections:
  • XLR4 - Power & RS485 data
  • BNC1 – HDSDI
  • BNC2 – Genlock

    Remote: Pan, Tilt, Zoom, Iris, Focus, Auto / Manual White, Preset White, Rgain,Bgain, Master Pedestal, Red Pedestal, Blue Pedestal, Shutter, Gain, Gamma, Dzoom On/Off, Auto Iris On/Off, Auto Focus On/Off, IR Mode On/Off, Chroma, Detail, Shading, Knee, WDR, RGB balance, Output Standard etc.Preset Store (P,T,Z,F), Preset Recall, GoTo Absolute Position,P,T reverse, speeds 1-10, Turbo Speed, ND Filter.

    Operating Temp: -10 to >+40degC Out of sunlight
    Sealed: IP65 minimum (IP66 option)
    Mounting:2 x 3/8”, 2 x 1/4” + safety bond point

    ‘DMX Control’:
  • 8 channels - Pan (2Ch), Tilt (2Ch), Zoom (2Ch), Focus (1Ch), Iris (1Ch)
  • 16bit positioning – 720deg. Pan

    Specifications subject to change without notice E & OE
  • For further information on the CamBall4 VRi download the CamBall4 VRi Brochure For further support on the CamBall4 VRi download the CamBall4 VRi Instruction Manual If you have any questions download the CamBall4 VRi FAQ For help with IP Multicaster Setup download the Instruction Manual