CamBall Lite

The CamBall Lite is still a fully featured version of the CamBall but at a reduced cost for indoor, lightweight use. It is build on the same CamBall chassis, it has the same motors and the same software inside. It has plastic covers and slip rings are not fitted. The diagnostic screen is also not available. Internally there are some other cost saving methods but none affect the performance, only the ruggedness of the standard CamBall is missing. This camera is good for uses where budgets are just a little tighter and where there is no requirement to locate it out of doors, and no applications where it would be subjected to the rigors that require the full CamBall4.

The CamBall has become a standard in the television and entertainment industries, consistently out-performing competitors, and this unit will do the same with its feature-filled performance, move smoothness and CCU control-ability.

All the same controllers work with CamBall Lite.

For further information, please download the Camball Lite brochure.

CamBall Lite

  • DMX, Free D, M*, Motion Control Protocols
  • Real Time Metadata for VR & AR
  • 64 Pre-set positions and moves
  • 2.4 Megapixel Sensor to 1080p
  • 12bit Digital Signal Processing
  • Enhanced CCU Control
  • Genlock
  • 1080i & 1080p
  • 30x optical zoom
  • Inverted or upright mounting
  • Switchable to Infra-Red Sensitive
  • Weight: 2.9kg
    Dimensions: W.166mm, H.222mm, D.206mm (+ connectors)
    Data: RS485
    Power: 12-16v @ 1A
    Pan Range: 300deg.
    Tilt Range: +/- 120deg from vertical.
    Pan Speed Range: <0.05deg/sec - >180deg/sec. Other ratios on request.
    Tilt Speed Range: <0.03deg/sec - >120deg/sec. Other ratios on request.
    Positional Accuracy: XM 0.083deg - VR 0.0055deg.
    Pre-Set Positions: 64
    Other Features: Profile Move with Ramp Up, Ramp Down, Total Time, Pan/Tilt Speed, proportional to zoom angle, LCD status screen, Tally Light
    Camera Sensor: 0.36” NMOS, 12bit DSP
    Active Pixels: 2.38 Mpixels
    Signal / Noise Ratio: >50dB
    Zoom: 30x optical
    HFOV: 64deg. to 2.3deg
    MOD: <30cm
    Distortion: <3% (wide)
    Iris: F1.6 - F28 – 256 steps
    Sensitivity: 1.4 lux. (F1.6 AGC On)
    HD Standards: 1080i/50/60, 720p/50/60, 1080p/50/60 HDSDI
    Connections: XLR4 - Power & Data, BNC1 – HDSDI, BNC2 – Genlock
    PTZ Remote: Pan, Tilt, Zoom, (fully proportional,) Iris, Focus, (positional), Pre-set Store (P,T,Z,F), re-set Recall, Profile Move Time, Profile Move Ramp Up, Profile Move Ramp Down, Profile Move Zoom Offsets, Absolute Position mode, P,T,Z,F reverse, speeds 1-10, Turbo Speed, Set Home, Goto Home, etc.
    CCU Remote: Auto / Manual White, Pre-set White, Rgain, Bgain, Ggain, Master Pedestal, Red Pedestal, Blue Pedestal, Shutter, Gain, Micro Gain, Gamma, Digital Zoom On/Off, Auto Iris On/Off, Auto Focus On/Off, IR Mode On/Off, Chroma, Detail, Shading, Knee, WDR, Dynamin Noise Reduction, RGB balance, Output Standard, ND Filter, Colour Bars, etc.
    Operating Temp: -10 to +40degC Out of sunlight
    Mounting: 2 x 3/8”, 2 x 1/4” + safety bond point
    Control Protocols: DMX (8 channels), Free D, Dstar, Mstar, (DMX model from CastSoft)
    Other Features: Wide Dynamic Range, Genlock, Enhanced CCU Control, Slip Rings, Inverted or Upright Mounting, Switchable to Infra-Red sensitive, Genlock, LCD status screen, Master/Slave mode, Tally Light
    For further information on the CamBall Lite camera, download the brochure